收藏本站
MTD10N10EL
12
Q T
90
75
1000
T J = 25 ° C
I D = 10 A
V DS = 100 V
8
V GS
60
100
V GS = 5 V
t r
45
t f
4
Q 1
Q 2
T J = 25 ° C
30
10
t d(off)
t d(on)
I D = 10 A
15
0
0
2
Q 3
4
6
V DS
8
0
10
1
1
10
1
Q G , TOTAL GATE CHARGE (nC)
Figure 8. Gate?To?Source and Drain?To?Source
Voltage versus Total Charge
R G , GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN?TO?SOURCE DIODE CHARACTERISTICS
10
8
6
4
2
0
V GS = 0 V
T J = 25 ° C
0.5
0.6
0.7
0.8
0.9
1.0
V SD , SOURCE?TO?DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define the
maximum simultaneous drain?to?source voltage and drain
current that a transistor can handle safely when it is forward
biased. Curves are based upon maximum peak junction
temperature and a case temperature (T C ) of 25 ° C. Peak
repetitive pulsed power limits are determined by using the
thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance?General
Data and Its Use.”
Switching between the off?state and the on?state may
traverse any load line provided neither rated peak current
(I DM ) nor rated voltage (V DSS ) is exceeded and the
transition time (t r ,t f ) do not exceed 10 m s. In addition the total
power averaged over a complete switching cycle must not
exceed (T J(MAX) ? T C )/(R θ JC ).
A Power MOSFET designated E?FET can be safely used
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non?linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E?FETs can withstand the stress of
drain?to?source avalanche at currents up to rated pulsed
current (I DM ), the energy rating is specified at rated
continuous current (I D ), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous I D can safely be
assumed to equal the values indicated.
in switching circuits with unclamped inductive loads. For
http://onsemi.com
5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MTD1114M3B PHOTODIODE
MTD1200M3B PHOTODIODE
MTD20P06HDLT4 MOSFET P-CH 60V 15A DPAK
MTD2955VT4 MOSFET P-CH 60V 12A DPAK
MTD3010N PHOTO DIODE 900NM DOME CLR TO-18
MTD3010PM PHOTO DIODE 900NM DOME CLR TO-18
MTD3055VL MOSFET N-CH 60V 12A DPAK
MTD3055V MOSFET N-CH 60V 12A DPAK
相关代理商/技术参数
MTD10N10ELT4G 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:TMOS E−FET Power Field Effect Transistor DPAK for Surface Mount
MTD1110 制造商:SHINDENGEN 制造商全称:Shindengen Electric Mfg.Co.Ltd 功能描述:Stepping Motor Driver ICs
MTD1110-4101 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MTD1110-4102 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MTD1110-4103 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MTD1110-7101 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MTD1110-7102 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MTD1110-7103 功能描述:马达/运动/点火控制器和驱动器 VCEO=80 IO=2 PT=5 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube